Product categories
More »
Stainless Steel
Stainless Steel specifications held in the austenitic, martensitic and precipitation hardening varieties. Stocks are held in British Standard and International standards. Below is listed our most commonly supplied grades; please contact our sales office. Also stock is 301 stainless spring temper rolled strip.
Hi-Steel HSLA-80
Hi - Speed, high Speed Steel Tool Steel (made) : highly processed into the Tool Steel, carbon content high, while containing cr quantity is low (about 4%), reason burnish of Steel surface gloss darker, after heat can reach by HRc62 high hardness, resistance to rust performance not on a roll.
Mould Steel
Steel mould and Steel mould suppliers, global delivery, stock supply Steel mould steels.
Heat Resistant Steel
Heat resistant steel. AS Orlov Izobret. Mashinostr. 3, 48-49, 7/2000. The purpose of this work was to increase plasticity of heat resistant steel after aging at the 500-1300 deg C temperature and to improve its operational reliability.
Tool Steel
Comprehensive stocks held of tool steel, including hot work, cold work and plastic mould tool steel specifications. Below we detail our most common grades. Other British Standard and international special steels and tool steels are also available, please contact our sales office.
Ball Bearing Steel
Supplies Ball bearing steel of all types, along with carbon steel and specialty balls, to OEM's around the world. Also offers platinum balls, brass balls, gold, titanium, aluminum, carbon and plastic balls.
Spring Steel
Carbon spring steel is held in a wide range of sizes. Detailed below are our most common specifications. Carbon steel strip and spring steel sheet is available most commonly in the hardened and tempered condition, though certain sizes are available in the annealed condition. Round and flat bar is stocked in the as rolled condition. Most spring steel specifications are held to British Standard steel specifications including BS1449 & BS970.
Alloy and Carbon Steel
Alloy steel is steel alloyed with a variety of elements in total amounts of between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is somewhat arbitrary: Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0 %.[1][2] Most commonly, the phrase "alloy steel" refers to "low alloy" steels.
News
More »
Enterprise email
Home » Tool Steel » Product introduction
AISI A2 Tool Steel
- Numbers: 2011030505
- Model: AISI A2
- Producers: China
- Update time: 2011.03.05
- Browse:
Product Description:
AISI A2 Air Hardening Tool Steel
-
(Machine finish) T & B WITH SAW-CUT EDGES
-
(Machine finish) FOUR SIDES
-
PRECISION GROUND
-
HOLLOW BAR
-
DRILL ROD
DESCRIPTION
An air-hardening Tool Steel containing five percent chromium. Replaces the oil hardening ( 0 1 type) when safer hardening, less distortion and increased wear-resistance are required. Provides an intermediate grade between the oil hardening and the high carbon, high chromium (d 2) types.
ADVANTAGES
-
Low distortion in heat-treatment
-
Good machinability
-
High abrasion-resistance and hardness
-
Good toughness for severe service
-
Deep hardening properties in large sections
TYPICAL ANALYSIS
CARBON…..1.00 MOLYBDENUM…..1.10 MANGANESE…..0.60
VANADIUM…..0.25 CHROMIUM…..5.25
HEAT TREAT
FORGING……………… 2000° to 2050° F, stop at 1700°F, cool slowly
NORMALIZING……… Do not normalize
ANNEALING…………. 1650° F, furnace cool, average Brinell 212
PREHEATING………… 1200° F, prior to hardening
HARDENING…………. 1775° F, air quench to 150°F
TEMPERING………….. 350° to 400° F, resulting hardness, Rockwell C 60-61
MACHINABILITY
Machines easily when properly annealed to 212 Brinell. Has a factor of 65 as compared with a one percent carbon Tool Steel which has a rating of 100.
TEMPERING RESULTS
The Rockwell C hardness obtained on specimens 1 in square when quenched in air from 1800° F, and quenched in oil from 1750° F and tempered at various temperatures are as follows:
| Hardness Rockwell C | ||
| Tempering Temperatures F |
1800 F Air-Quench |
1750 F Oil-Quench |
| None | 64 | 65 |
| 300 | 62 | 62.50 |
| 400 | 60 | 61 |
| 500 | 56 | 57.50 |
| 600 | 56 | 56 |
| 700 | 56 | 56 |
| 800 | 56 | 56 |
| 900 | 56 | 56 |
| 1000 | 56 | 55 |
| 1100 | 50 | 50 |
| 1200 | 43 | 45 |
| 1300 | 34 | 34 |
These results may be used as a guide in tempering tools to desired hardness. However, since 1 in. specimens were used in this test, tools of heavy section or mass may be several points lower in Rockwell hardness for a given treatment.
Steel classification：
Stainless steel，Hi-Steel HSLA-80，Steel mould,Heat resistant steel,Tool Steel,Ball bearing
steel,Spring steel,Alloy steel,Construction steel，Die steel，Mould steel.
Product description：
Step Shaft AISI A2 Tube AISI A2 Pie-shaped AISI A2 Ring AISI A2 Module AISI A2 Large valves of
the main AISI A2 Other Profiled forgings AISI A2
Products Introduction :
Specialized and high quality steel.
We have the advantages of equipment, technologies and price.
Specifications
Round bar ：
Diameter : 1mm-2000mm
Square bar:
Size： 50mm * 50mm-600mm *600mm
Plate steel/flat bar:
Size：Thickness:0.1mm-800mm Width:10mm to 1500mm
Tube/pipe:
Size：OD:6-219mm WT：1-35 mm.
Cold-rolled sheet:Thickness:2-5mm Width:1000mm Length:2000mm
Hot-rolled sheet:Thickness:6-80mm Width:210-610mm
Length: We can supply any length based on the customer's requirement.
Forging/hot rolling/ extrusion of steel.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching
+ tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on
the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable
electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the
customer's requirement
Excellent service for all kinds of industries,with advantages of technologies, equipment and
price.
We serve you with our honesty, integrity, and professionality.
